---
title: "Monitoring wireless radios"
description: "Add point-to-point and point-to-multipoint radios as Wireless devices, check that the manufacturer and model match a supported template, and read the Wireless list, the Radio Performance chart per chain, radios, interfaces and radio links."
---

> Documentation Index
> Fetch the complete documentation index at: https://netsense-nms.com/docs/llms.txt
> Use this file to discover all available pages before exploring further.

# Monitoring wireless radios

Wireless radios are a device type of their own in NetSense. A radio added as a **Wireless**
device gets its own section in the menu, a device page with signal quality per RF chain
(SNR, RSSI, Tx power, noise floor and PHY rate), and its own alarm types, next to the
traffic, ping and health data every device gets.

Coverage is narrow today and this page is explicit about it: only the models in the next
section are polled.

## Supported radios

| Manufacturer | Model | Notes |
| --- | --- | --- |
| Mimosa | Any model | All Mimosa models use the C5x template |
| Airspan | C5x | The same hardware, reporting itself as Airspan |
| MikroTik | RB SXT G-5HPnD r2 | This exact model only |

The template is picked from the **manufacturer and model names** on the device, and for
Wireless devices the match is strict: the spelling must be exactly as in the table
(capitalization does not matter). Any other manufacturer or model, including other MikroTik
boards and Ubiquiti or Cambium radios, is **not polled at all**. The device stays
**Unknown**, with no uptime, firmware or radios, and nothing in the UI says why.

So if a new radio stays Unknown, check the manufacturer and model spelling against the
table above and [supported vendors](https://netsense-nms.com/docs/reference/supported-vendors/#wireless-vendors)
first. For any other model, ask Extreme Labs: support for a new radio is added per model.

## Adding a radio

Wireless devices are added by hand, one at a time:

1. Go to **Inventory → Devices → Create Device**.
2. Set **Device Type** to **Wireless**.
3. Enter the **Hostname**, the management **IP Address** and the **SNMP Community**.
4. Pick or type the **Manufacturer** and **Model** exactly as in the table above. For a
   Mimosa radio, use the manufacturer **Mimosa** and the model the radio reports, for
   example C5x.
5. Save. The radio is polled by the agent like any other device, so its SNMP access list must
   allow the agent's IP.

The rest of the form (zone, site, partner, SNMP settings) works as for any device. See
[adding devices](https://netsense-nms.com/docs/guides/adding-devices/). Editing a Wireless device needs
`wireless:edit`, the same way `switch:edit` covers switches.

For a point-to-point link, add **both ends**: each radio is its own device.

## The Wireless section

A **Wireless** entry appears in the sidebar as soon as the first wireless device exists in
the tenant. It has two children:

- **Ports**: every port on every radio, with its device, bandwidth, utilization and last
  state change.
- **Radio Links**: the links NetSense has paired from both ends, with **Point A Device** and
  **Point Z Device** (each with its interface), the link **Status** (**Connected**,
  **Disconnected** or **Unknown**) and **Last Observed**. See [Radio links](#radio-links-and-connections)
  for when this list fills.

The Dashboard also gets a **Wireless Overview** tab, and wireless radios count in the
[All Devices dashboard](https://netsense-nms.com/docs/guides/dashboard/).

## The Wireless list

The list shows one row per radio. The default columns are status, hostname, a ports
summary, the number of **Radios**, **Packet Loss (%)** and **RTT (avg ms)** from the agent's
ping, temperature, CPU, RAM, bandwidth and the last update. CPU and RAM stay empty on
radios that do not report them.

![The Wireless device list with four radios and their status, ports summary, number of radios, round-trip time, temperature and bandwidth; all four radios were down when it was taken, so temperature and bandwidth are empty](https://netsense-nms.com/docs/_nimbus/md/1y3i0se/wireless-list.png)

Select radios to export them as CSV, or to poll them now with **Refresh Wireless** (needs
`wireless:report`).

## The device page

### Overview

The **Overview** tab has the charts every device has (**Wireless Performance** with traffic,
latency, loss and jitter, and **Wireless Health** with CPU, RAM and temperature), plus the
**Radio Performance** chart:

| Tab | What it shows |
| --- | --- |
| **PHY Rate** | Tx and Rx PHY rate: the modulation rate the link is running at, not the traffic |
| **SNR** | Signal-to-noise ratio per chain, in dB |
| **RSSI** | Received signal strength per chain, in dBm |
| **Tx Power** | Transmit power per chain, in dBm |
| **Noise Floor** | Noise floor per chain, in dBm |

Every chart has one line per RF chain (**Chain 1**, **Chain 2**, …), so when one chain of a link
degrades while the other holds, the two lines drift apart and it shows at a glance. On a device with more than one radio, a selector next to the title
picks the radio.

![A point-to-point radio's Overview with the Radio Performance chart on SNR showing Chain 1 and Chain 2 over the last 24 hours, the periods when the radio was down shaded red, and the Radio Information panel with the radio's frequency](https://netsense-nms.com/docs/_nimbus/md/ij3kpc/wireless-radio-performance.png)

**Radio Information** in the right-hand panel lists the number of **Physical Radios** and, for
each radio, its channel or center frequency.

### Radios and Wireless Interfaces

- **Radios** lists each radio with its **Band**, **Channel**, **Frequency** and **Width**,
  **PHY Rate** (Tx / Rx), SNR / RSSI and Tx Power / Noise Floor (averaged over the chains),
  the number of wireless interfaces and **Last Updated**. Expand a radio for its history.
- **Wireless Interfaces** lists the radio interfaces with their **Mode** (AP or Station),
  **MAC**, **SSID**, **BSSID**, **Security** and **Broadcast**.

Both tabs need `wireless:radio:view`. **Ports** (with `wireless:port:view`), **Alarms**,
**Syslog**, **Topology**, **Links** and **Poller** work as on other device pages.

### Radio links and connections

Two more tabs appear only when the radio reports the peers it is talking to:

- **Connections**: each peer seen on a local interface, with the remote interface, status,
  PHY rate, bandwidth, packets and **Last Observed**. Expand a row for its traffic.
- **Radio Links**: the link this radio is part of, paired with the device at the other end.

Not every radio reports its peers. **Mimosa and Airspan C5x radios do not**, so on a C5x the
Connections and Radio Links tabs do not appear, and the **Radio Links** list in the sidebar
stays empty even when both ends of the link are in NetSense. Their signal, PHY rate and
traffic are still collected in full. The MikroTik RB SXT G-5HPnD r2 can report peers from its
registration table, so the tabs appear on it once it has registered peers.

## Alarms

Wireless devices have two alarm report types of their own in
[alarm definitions](https://netsense-nms.com/docs/guides/alarm-definitions/):

- **Wireless**: device-level values such as status, ping results, CPU load, memory load,
  temperature and uptime.
- **Wireless Port**: port status, traffic and utilization, errors, discards, packet rates
  and speed.

Radio values (SNR, RSSI, PHY rate, noise floor) are charted but are not alarm fields.

## Permissions

| Key | What it allows |
| --- | --- |
| `wireless:view` | See the Wireless section, list and device pages |
| `wireless:edit` | Add and edit wireless devices |
| `wireless:report` | **Refresh Wireless** on selected radios |
| `wireless:port:view` | See wireless ports and the **Ports** list |
| `wireless:port:edit` | Edit port descriptions and settings |
| `wireless:port:delete` | Delete a port |
| `wireless:radio:view` | See the **Radios**, **Wireless Interfaces** and **Radio Links** views and the radio count |

The built-in roles have them already: **viewer** gets the three view permissions, **admin**
and **editor** get all seven. Custom roles need them added by hand. See [users, roles and partner access](https://netsense-nms.com/docs/guides/users-roles/).

## Node count

A wireless device counts as one node, plus one node for each of its ports and one for each
radio. Tenant admins see the live count under **Reports → Pricing**. See
[how licensing counts nodes](https://netsense-nms.com/docs/reference/faq/#commercials).

## Limits

- Only the three manufacturer and model pairs above are polled. Everything else stays
  **Unknown** with no explanation in the UI.
- Radio links need the radio to report its peers. Mimosa and Airspan C5x do not.
- There are no alarms on radio values such as SNR or RSSI yet.

Source: https://netsense-nms.com/docs/guides/wireless-devices/index.mdx
